Check back regularly or subscribe for updates. Email us at jandkaudiodesign@gmail.com, or fill in the form on the left.

Saturday, January 16, 2016

Power Factor Correction

Recently, a few buddies of mine have been very interested in products that will improve the mains power. There are many products of such nature, like isolation transformer, mains regulator, power factor corrector, power bank, and etc. Isolation transformer, mains regulator and power factor corrector are widely understood, but what is power bank? Can we really store power?

One of the gist of better power transmission is power factor correction. This has been widely used in industrial or commercial buildings to correct the phase relationship between voltage and current to achieve better (close to 1) power factor. Power factor of 1 means there is perfect alignment of voltage and current phase to achieve perfect 100% power transmission. Power factor of <1 means there is a phase shift between Voltage and Current, and power delivery is less than idea.

The phase relationship of the Voltage and Current is dependent on the electrical equipment connected on the load. Say, if we fixed the Voltage phase as reference (as usual, we always need a reference point), there shall be loads that shifts the Current forward and backward in relation to the Voltage phase. In general, inductive load will shift the current backward since inductor prohibits current flow (high impedance to current change), and capacitive load will shift the current forward, in relation to Voltage. Resistive load, is phase neutral - does not shift the current in relation to voltage.

Most solid state uses very big capacitor bank and therefore causes current to advance in phase in relationship with voltage. On the other hand, tube amplifier uses a lot of chokes and transformers, with low capacitance but high voltage capacitors, therefore current will retract in relationship with voltage.

Current / Voltage Phase Relationship

How do you correct this relationship? Simple! The answer is already there! If the current advances in relationship with voltage, use inductor to pull it back, and vice versa! This is called power factor correction (PFC)in lay man's term! One of the difficulties with power factor correction is that how much is enough and how much is too much? There is NO benefits in over-correcting. A close to 1 power factor will not only make your system sounds better, but saves you money too!

In industrial designs, usually a micro-controller is used to monitor the current versus phase relationship, and change the compensation in a controlled feedback loop. Less complicated system can use fixed PFC, like switch mode power supplies with PFC integrated.

PFC works, but can passive PFC like the above work for your system? Yes, it can, but not always the case since everyone's systems are different! Once would have to get the right PFC factor right to have the optimal correction and optimal sound. A one size fits all solution does not work. If it works, you are lucky, or it is just sound changes instead of optimization with over or under-corrected power factor.

In the next article, we shall come up with a simple user configurable power factor correction device. Once can flip switches to change the PFC factor to customize it to their own systems. It might be hard without measurement devices but at least one can still use their ears and that's what matters!

J&K Audio Design
1/17/2016

Product Lists  

Level 0

Level 3: depends on type, size and complexity. Email us for details.
Iso-trans: link 1, link 2
* Finished amplifiers, DACs, audio gadgets, upgrades and repairs - this is not our core business and we do it out of passion. We do not have fixed models, fixed price and we customize for each individuals. The sky is limit of creativity.  
* Our product lines are always improving and increasing. If you do not see what you want, contact us!  
* Please email for volume discounts, distributor and OEM pricing.











Friday, January 15, 2016

Western Electric Transformers

Imaging Star Wars music playing at the background - "Imperial March"

Attack of the WE chokes and OPT fighters... The force is strong with this one... Once tried, there's never going back.


WE choke

Original WE core

Fleet of WE fighters
Western Electric Output Transformers



We often hear people saying that WE output transformers is good in mids, smooth and warm but lack of high and low frequency extension. That is because they do not understand the Western Electric core as well as we do. 

In order to have high primary inductance, one has to have more turns in the primary, and that reduces the high frequency response, and vice versa. It is not easy to achieve a balance between the two and often people gave up with less optimal results. We do not. We aim for the best!

Take a look at our WE OPT primary inductance specifications below, and also the bandwidth. We are not all talk and no results. 

          Primary impedance: 15K
Primary inductance: 114H(112H)(DC bias at 10mA,20Hz,5Vrms)
Bandwidth:7Hz – 60kHz at -3dB
Audible bandwidth is almost flat: 20Hz (-0.76dB) — 1 KHz (0db) — 20 KHz (-0.41dB)
More pictures added (1/21/2016)




 

J&K Audio Design
1/16/2016

Product Lists  

Level 0

Level 3: depends on type, size and complexity. Email us for details.
Iso-trans: link 1, link 2
* Finished amplifiers, DACs, audio gadgets, upgrades and repairs - this is not our core business and we do it out of passion. We do not have fixed models, fixed price and we customize for each individuals. The sky is limit of creativity.  
* Our product lines are always improving and increasing. If you do not see what you want, contact us!  
* Please email for volume discounts, distributor and OEM pricing.

Thursday, January 14, 2016

Chinese New Year 2016 Break

J&K will have Chinese New Year break from 1st Feb 2016 till 14th Feb 2016. Customer service will still take orders but no production will run during this time.

Our custom orders queue to deliver before Chinese New Year is currently full. Orders taken now will only be delivered after Chinese New Year break. Please place your order early if you want to get your order delivered soon after the break.

Thank you for your patience!

Happy Chinese New Year to all our customers! 

J&K Audio Design
1/14/2016

Product Lists  

Level 0

Level 3: depends on type, size and complexity. Email us for details.
Iso-trans: link 1, link 2
* Finished amplifiers, DACs, audio gadgets, upgrades and repairs - this is not our core business and we do it out of passion. We do not have fixed models, fixed price and we customize for each individuals. The sky is limit of creativity.  
* Our product lines are always improving and increasing. If you do not see what you want, contact us!  
* Please email for volume discounts, distributor and OEM pricing.

Tuesday, January 12, 2016

Supercharger Amplifier

  • Have you ever felt that you are lacking of power in your amplifier?
  • Have you got stuck because your existing amplifier has nostalgic value?
  • Have you thought of upgrading but still like the tone of your current amplifier? 
  • Have you imagined that what would happen if you have a couple of Watts more? 
  • Have you ever liked a speaker so much but it is too difficult to drive for your existing amplifier that you liked so much too? 
  • Have you imagined what a supercharged 45, 2A3, 50, 300B, or any low power direct heated tube would sound like?
Now here lies the answer! 

We have heard of pre-amplifier, power amplifier, integrated amplifier, and various amplifiers. Supercharger amplifier is a rare term, isn't it? 

This is not something new but it is not that common in tube amplifier world. A supercharger amplifier is THE power amplifier for integrated and power amplifiers -> power power amplifier? LOL... That would be funny, right? Therefore, supercharger amplifier or turbo amplifier will be a better term to use.

What it does is to boost the power of the existing amplifier by manifolds! What one needs to do is to connect the speaker output of the current / existing amplifier (yes, the speaker output to the supercharger amplifier, and the outputs of the supercharger amplifier are connected to the speakers. The picture above shows how it is connected. Simple isn't it? 

Some might ask, why can't I take a high power amplifier in the market, and connect it in such a way? Well, unless it is designed to work this way (like Musical Fidelity 550K Supercharger), most amplifiers aren't destined to work this way. The powered output from the existing amplifier would have overloaded the input stage of the high power amplifier and fried the amplifier. Also, there would be redundancy in the amplifier since the high power amplifier would have their own pre/driver stage to properly drive the power stage into full power. We would miss all the goodies (tonality, character, and etc) that the existing power amplifier would bring too. 

What we need is a supercharger amplifier that does not have the pre/driver stage, that could make full use of the goodies brought over from the existing high quality amplifier - direct drive, with honest transfer of the characteristics from the source lower power amplifier to the supercharger amplifier! In order to do so, the best possible way would be to introduce a high inter-power-stage transformer with a high step up factor to produce the signal drive required by the supercharger amplifier with a direct power stage. 

One might ask, can I connect an ordinary output transformer in reverse to do so? Yes, you can! It will work, but not optimally! The gain might not be right. The design of the output transformer is not suited for power to voltage conversion too. Ordinary output transformer converts high impedance to low impedance as a means of power transfer. The inter-power-stage (IPS in short) transformer is for voltage amplification. 

The secondary reflected to primary distributed capacitance will affect/change the distributed capacitance and the inductive resonance of the transformer. As output transformer secondary is always low impedance, the resonance will be attenuated by the load (therefore output transformer secondary must always be connected to a load). 

For IPS, the secondary of the transformer is always appeared to be open or at high impedance due to being connected to tube grid and grid leak resistor. With that, the resonance is fully reflected to the primary. This will have negative impact on the operation of the amplifier and therefore is not recommended to use ordinary output transformer as IPS. Of course there is a way to design an output transformer that can work as an IPS but this is something of a compromise and is not recommended. 

Some others might ask, can I use an ordinary step-up transformer to do the job? Yes, you can, if the step-up transformer is designed for this task - if it is with sufficient core size to handle the high signal level, and with heavier gauge cables to handle the current.



Above is a famous direct coupled Loftin White 2A3 amplifier. Needless to say, it is a great sounding amplifier. The only drawback is the limited output power to drive common speakers. What we can do here is to use a supercharger amplifier to boost the output power to a decent 40W-50W level, such as using the famous 212 tubes, be it NOS, or from new manufacturers. The supercharger amplifier is designed with very minimum components, and therefore it posses the least character or coloration of its' own, and is much cheaper & simpler to manufacture too. Of course, other power tubes like 211, 845, 833 and such can be used too with great results.

Where can we get these IPT (inter-power-stage) transformers to build/design the Supercharger Amplifier? Good new is, J&K has it, and we are offering it as our Level 2 and Level 3 custom made models for IPT. Sorry, we cannot do it at Level 0 or Level 1 for now due to the complexity involved, and the effort we spent to develop these IPT. Here are the prices in matched pair, rated at 10W power handling.

Level 2 IPT - U$590 (for driving 211, 212 and less demanding tubes)
Level 2 IPT - U$790 (for driving 845, 833 and high demanding tubes)
Level 3 IPT (1:5 step-up) - U$1090 (for driving 211, 212 and less demanding tubes)
Level 3 IPT (1:10 step-up) - U$1490 (for driving 845, 833 and high demanding tubes)
Level 3 IPT (1:20 step-up) - U$2290 (for driving 845, 833 and high demanding tubes)

Now isn't this a GREAT news?  

For those that wants a fully built system, please email us for more details and quotation. 

One warning for the users though - remember this rule - garbage in, garbage out. All the shortcomings or all the greatness of the existing amplifier will be amplified manifolds with such design topology.

J&K Audio Design
1/12/2016

Product Lists  

Level 0




Level 3: depends on type, size and complexity. Email us for details.

Iso-trans: link 1, link 2
* Finished amplifiers, DACs, audio gadgets, upgrades and repairs - this is not our core business and we do it out of passion. We do not have fixed models, fixed price and we customize for each individuals. The sky is limit of creativity.  

* Our product lines are always improving and increasing. If you do not see what you want, contact us!  
* Please email for volume discounts, distributor and OEM pricing.


Friday, January 8, 2016

Western Electric Output Transformer


Looking for Western Electric Output Transformer? Or looking for the Western Electric Sound, that you cannot forget after listening to a Western Electric audio gear? Seek no further - your holy grail is here.

This is a pair of Level 3 output transformer, made with genuine Western Electric 1038A (other sizes available, please email for more details) EI 76 transformer core. It is categorized as Level 3 due to the difficulties to get it to such specifications, where the primary and secondary are both very high impedance - 15K primary, 600 Ohm secondary! You are encouraged to seek out similar output transformers and compare the specifications to this.

On top of that, Western Electric 1038A core does not have the excellent electrical properties of modern Z11 or NanoCrystalline core and therefore is MUCH harder to get the right combination to get such wide and flat bandwidth.

Do not be fooled by the inferior frequency response compared to our Z11 or Nanocrystalline Double C core Level 3 transformers. Their frequency responses are still excellent and better than A LOT of the transformer out there. In addition, they have the warmth, tonality and smoothness that the Western Electric core is famous for. 

This pair is made for 5687 - 6SN7 use. Other specifications is upon request. Contact us to customize your own Western Electric output transformers! 

Level 3 Nanocrystalline Double C Core Preamp Output Transformer


Technical Parameters

Measured response (output in phase): 
20Hz (-0.76dB) — 1 KHz (0db) — 20 KHz (-0.41dB)

Measured response (output out of phase): 
20Hz (-0.76dB) — 1 KHz (0db) — 20 KHz (-0.54dB)



Primary impedance: 15KΩ

Secondary impedance: 300Ω

Core: Western Electric WE 1038A EI76

Primary DCR: 905.4Ω(908.3Ω)(B-P,9℃)

Secondary DCR: 37.9Ω(38Ω)

Primary inductance: 114H(112H)(DC bias at 10mA,20Hz,5Vrms)

Primary max DC: 30mA (recommend <= 10mA)



Measurement conditions: 6SN7 paralleled (3.85K Rp), Vplate 200V, 8mA total, fixed bias, secondary 10K Ohm resistive load, 1Vrms input at grid). 



Matching

Primary copper loss < 2%(<= 4 Ω)

Primary inductance < 5%(<= 2H)



Notes: For tubes with ~7K or less Rp, i.e.: 6SN7, 6J5, 5687, 6DJ7, 12AU7, E88CC, and etc. The lower the Rp, the better the frequency response and linearity.



Actual measured FFT response with 6SN7 in parallel:

Secondary in phase: 7Hz to 50kHz -3dB
Secondary out of phase:7Hz – 60kHz -3dB

Western Electric 1038A EI 76 Transformers





J&K Audio Design
1/8/2016

Product Lists  

Level 0

Level 3: depends on type, size and complexity. Email us for details.
Iso-trans: link 1, link 2
* Finished amplifiers, DACs, audio gadgets, upgrades and repairs - this is not our core business and we do it out of passion. We do not have fixed models, fixed price and we customize for each individuals. The sky is limit of creativity.  
* Our product lines are always improving and increasing. If you do not see what you want, contact us!  
* Please email for volume discounts, distributor and OEM pricing.

Search This Blog

Product Lists

Product Lists

Level 0: link 1

Level 1: link 1, link 2, link 3, link 4

Level 2: link 1, link 2, link 3, link 4, link 5, link 6, link 7, Link 8, link 9

Level 3: depends on type, size and complexity. Email us for details.

Iso-trans: link 1, link 2

Power-trans: link 1

* Finished amplifiers, DACs, audio gadgets, upgrades and repairs - this is not our core business and we do it out of passion. We do not have fixed models, fixed price and we customize for each individuals. The sky is limit of creativity.

* Our product lines are always improving and increasing. If you do not see what you want, contact us!

* Please email for volume discounts, distributor and OEM pricing.