Check back regularly or subscribe for updates. Email us at jandkaudiodesign@gmail.com, or fill in the form on the left.
Showing posts with label Amplifier Design. Show all posts
Showing posts with label Amplifier Design. Show all posts

Thursday, June 30, 2022

Balanced tube filament winding

Balanced power for mains has been known for ages and it brings tremendous improvement to the sound of many audio setups, especially with our Level 3 Ultra Isolation Transformers or Level 3 Ultra Isolation Power Transformers custom made for audio amplifiers. 

Balanced LV filament winding


Why do we still want to bring this up then? 

Take a look at the above schematic. What can you see different from the ordinary tube amplifier schematic with tube rectifier design? Yes, the filament winding as a center-tap and is balanced. 

Since we manufacture a lot of custom made power transformers, we do not see the the common usage of balanced filament windings for tube rectifier filament supply. It is quote common for the B+ / HT supplies, but not the LV filament supplies. LV filament supply is often quoted as 5Vac or 6.3Vac, but not as 5VCT or 6.3VCT with a center-tap, which is also a balanced winding? 

Why not? Since it is custom made power transformers, one should consider balanced LV filament windings as well to gain all the benefits of balanced winding and the noise cancellation/immunity properties it brings. 

Till then. Take care everyone! 

J&K Audio Design

1/5/2022 










Saturday, May 25, 2019

Class A Amplifier

Trying out a MOSFET class A amplifier. 
Something for a change once in a while after trying so many tube amplifiers.
Pretty decent I would say! 
If added with a tube preamp, it will be just perfect! 


Frequency response measured on scope.








J&K Audio Design
25/5/2019

Wednesday, June 20, 2018

SIT Amplifier with 2SK180

Below is an interesting amplifier design from M. Rothacher.

It uses SIT (Static Induction Transistor). SIT characteristics is quite close to vacuum tube Triode. Based on many user's feedback online is that SIT sounds quite close to Triodes! 



SIT, THF-51S, 2SK180, 2SK180ES and such are very high power devices with PD of ~400-1KW. Say we take 15% as efficiency of class A amplification, we can easily get 60W - 150W out of SIT! This is definitely more economical and simpler than to draw 50W out of a 212 tube. 

A level 1 OPT, tailored for this above application
- Z11 - U$490/pair, Z9 - U$590/pair.
- Pri: 250 Ohm (configurable), inductance ~1H 
- Pri DC: 1A (others are available) 
- Second: 0-4-8-16R (any)
- Output power: 70W

Some samples bias settings (not tested):




A sample circuit from Nelson Pass, in his SIT Nemesis article: 


This looks alike to a normal SPUD circuit and is simple enough for DIYers with experience on building tube amplifiers. 

It would be quite interesting and ear opening to try out such designs.

J&K Audio Design
21/6/2018 

Monday, June 11, 2018

Miller Effect on Resistive Attenuator

Have you ever wondered, why TVC, or AVC are much better sounding that resistive attenuator, or resistive volume pot? 

The answer(s) to why transformer / autoformer based volume control is better than resistive volume pots, is quite complex, as there are many factors to it. But, one that stands out, that many may not be aware of, is the Miller capacitance + volume pot effect, that caused the amplifier bandwidth to be reduced significantly when used with a resistive attenuator, or resistive volume pot. This is especially significant if a high value volume pot is used, such as 100K-250K pot.

Everyone knows about Miller capacitance, and why grid stoppers are required, right? But, is he aware that volume pot is part of grid stopper too?

The resistance from the pot has the same effect as a grid stopper (The resistance, starting from input of source, to the volume pot viper section,  is part of the grid stopper!), creating a RC low pass filter with the input capacitance of the tube connecting to the volume pot. This RC low pass filter will attenuate any content above the cut-off frequency. 

The cut-off will be worsen by higher gain tube as the Miller capacitance is multiplied by the gain, in simple calculation sense, a good example, will be 12AX7. (Could it be the same reason where some prefers lower gain tubes in their amplifier instead of a high gain ones?)

Take 12AX7 as an example, the Cin (Miller capacitance) will be ~200pf, give a  take a few or tens of pf. 

Say, with 100K Ohm resistive volume pot, the setting now is at mid point of 50K, indicating that there's a 50K+ "effective grid stopper" connected to 12AX7. Ignore the actual grid-stopper connected for the moment. With that, the resultant cut-off shall be:

f cut-off = 1 / (2 * pi * Rg * C) = 1 / (2*3.142*50,000*200pf) = 16kHz (!!!) 

That's a freaking 16kHz low pass RC filter in the amplifier without one even realizing it. That is sad...

That's why a lot of folks prefer TVC or AVC versus resistive volume pot. That's why most people will say that the realism is better, the highs are airier and with more body once they migrated to TVC or AVC. Once they tried TVC or AVC, they will never go back to resistive volume pot.

Till then. Go figure.

J&K Audio Design
6/11/2018



Saturday, March 10, 2018

ED8000 tube amplifier schematic

When I'm talking about NOS Telefunken tube amplifier, it gets me excited and makes me sleepless! 

For those that are unaware of the previous article, please visit:  
http://jandkaudiodesign.blogspot.my/2018/03/ed8000-tube-amplifier.html

Here goes revision 1 of our proposed ED8000 tube amplifier design. There are tonnes of methods to build ED8000 tube amplifier. Below ED8000 tube amplifier schematic is just one of them, a simple one in fact. It needs only 1pc of 5687 to drive both Left and Right channels, with the use of 1:2 step-up input transformer to provide sufficient gain to drive ED8000 tube to full power.




P/S: circuit has not been tested yet, further fine tuning may be required.


Other than the usage of 1:2 input transformer, there is the innovative use of a 200H plate choke for 5687 as load to keep the B+ low to match the B+ of ED8000, where B+ is quite low compare to other tube amplifiers such as 2A3 or 300B. If resistive load is used for 5687, then the Vplate of 5687 needs to be lower so that the B+ needed does not exceed 177V. 

Or, use interstage transformer! With interstage transformer, ED8000 grid leak resistor can be removed, together with the coupling capacitor, which is an even more elegant and better sounding design. Of course, interstage transformer comes with a slightly heftier price tag.

All the components for the ED8000 single ended tube amplifier schematic are carefully calculated for the best effects and are not simply plugged from the sky. If you copy the design, please do not change the values of the components used. If you change it, and it does not sound good, blame yourself! LOL. 

The B+ can be slightly tuned by adding a small capacitor of 0.1U - 0.68U after 5U4 rectifier tube rectifier. This converts the choke-input rectification to pseudo capacitor-input, and raise the B+ slightly.

If you build it and like it, let us know! If you need the irons, let us know too! If you see errors in the design, let us know. It was designed in a matter of minutes.

Enjoy!

J&K Audio Design
11/3/2018

ED8000 Tube Amplifier

Let's talk about a slightly different topic today, ED8000 tube and how to use ED8000 in Single Ended Amplifier! 



Little has been said about this tube in the internet. We've Google and didn't find much articles on ED8000 in tube amplifiers. This tube often appears in eBay at very decent price still, considering it is a Telefunken tube (perhaps audiophiles do not like it since it is supposed to be a series/pass regulator tube). Most are German made (Valvo, Telefunken and Siemens) and price are quite decent too, around U$10 - 50/pc, depend on whether it is NOS or used. We suspect all of them are from Telefunken factory (anyone can confirm?).


Datasheet:
http://tdsl.duncanamps.com/pdf/ed8000.pdf

Why do we like this ED8000 tube? There are a few reasons! 

1. We love Telefunken tubes. Most sound good, and very reliable.
2. It is a long life tube, guaranteed for 10,000 hours operation.
3. Tight tolerances grade (Telefunken tubes are known to have tight tolerances even for the general type).
4. Special grade vibration and shock proof tubes.
5. High transconductance and low Rp (easy to make the output transformers). 
6. It is a TRIODE! 



If the circuit is made right, we can actually make an ED8000 tube amplifier that is compatible with 6AS7 / 6080 tube! 6AS7 / 6080 SET, to some, are poor man's 300B amplifier. Their Rp, operating point, output transformers and other electrical parameters are close enough to be made compatible. Do no try this at home! Only special made amplifiers can do this.

Looking at the ED8000 tube Ia/Ua curve, with Pa =17W, the tube can be biased at 140V plate, 100mA Iplate, and -26V Vgrid. That gives Pd = 82%, which is near the 75% ball park, which is the usual values that one would bias their tubes for class A operation. Since this is a special quality tube, I do not mind biasing it hotter to get more power out of this. 



With such bias, ED8000 needs only 52Vpp to bring it to full power. A simple 2 stage driver will be sufficient, such as 6SN7-6SN7, or 5687-5687. If one employs a step-up interstage transformer of 1:2 (recommended), single driver tube will be enough. Or, go for a higher gain driver tubes, for example: 5842 / 417A, EC8010, E55L / 8233, 6SL7, 12AX7 and similar tubes. Low Rp tube are recommended though to have better bandwidth.

Output power of ED8000 single ended amplifier will be around 3W-4W, depending on what distortion figure you are looking at. It is a poor man's 2A3 SET. ED8000 is priced like a Chinese 2A3 replicas, and you get old school Telefunken quality (sound!)! This is definitely worth considering.

With high quality OPT (from us of course, LOL!) to go with (not difficult to make since primary impedance is only ~1K Ohm, no complex winding scheme is required), it should be awesome. Did I mention that it can be a good headphone driver too?

Important note: with high transconductance tubes such as ED8000, cathode bias is recommended to prevent runaway. I would use a CCS at the cathode to keep it locked in place. 

Now, go build it and let us know how it goes! Let us know if you need the transformers to go with this wonderful ED8000 tube. We can supply a whole kit to you.

J&K Audio Design
10/3/2018

Search This Blog

Product Lists

Product Lists

Level 0: link 1

Level 1: link 1, link 2, link 3, link 4

Level 2: link 1, link 2, link 3, link 4, link 5, link 6, link 7, Link 8, link 9

Level 3: depends on type, size and complexity. Email us for details.

Iso-trans: link 1, link 2

Power-trans: link 1

* Finished amplifiers, DACs, audio gadgets, upgrades and repairs - this is not our core business and we do it out of passion. We do not have fixed models, fixed price and we customize for each individuals. The sky is limit of creativity.

* Our product lines are always improving and increasing. If you do not see what you want, contact us!

* Please email for volume discounts, distributor and OEM pricing.